Home > Error V > Vxvm Vxdg Error V 5 1 10127

Vxvm Vxdg Error V 5 1 10127

Contents

Available, used and free memory in AIX Use lsattr to get the size of your memory: # lsattr -E -l sys0 | grep realmem realmem 32636928 Amount of usable physic... Unfreeze the service groups:# hagrp -unfreeze For systems running Cluster Volume Manager1. Use Ignite-UX to rebuild the rootdg diskgroup The safest method to resolve this alignment problem is taken a system image of the whole rootdg using Ignite-UX recovery commands and rebuild the ORA-02082: a loopback database link must have a connection qualifier I have two Oracle databases, one 9.2.0.8 (SID test9) and another 10.2.0.4 (SID test10). Check This Out

Suggested solution: The dynamic tracking and fast fail features of AIX 5.2 ML3 (5200-03) can be used to address this problem. Resolution:This is a known issue and fixed in following patches.Solaris : 4.1MP2RP3 / 5.0MP1RP4Workaround:This issue can be immediately corrected by restarting the vxconfigd daemon.  See the following for details on how Preventing access to a disk by Volume Manager When Volume Manager starts up, it accesses every disk on the system by reading its disk header and possibly a few blocks from It should be used only by a system administrator who is trained and knowledgeable about Volume Manager. https://www.veritas.com/support/en_US/article.TECH52689

Error V 5 1 10127

Even if writes are only made to the snapshot volume, vxassist snapprint shows the same "%DIRTY" value for the original volume. No Yes Products Products Home Threat Protection Advanced Threat Protection Endpoint Protection IT Management Suite Email Security.cloud Data Center Security Information Protection Data Loss Prevention Encryption Validation & ID Protection Managed As a result, some volumes may not be started when an application starts after reboot. Close Sign In Print Article Products Article Languages Subscribe to this Article Manage your Subscriptions Problem Getting error "Disk and diskgroup versions are incompatible" when adding a new disk of

There is no Start Volume action. Adding Nagiosgraph to Nagios This article is an update to my prior released article about installing Nagios in Slackware . Submit a Threat Submit a suspected infected fileto Symantec. Error Message VxVM vxmake ERROR V-5-1-10127 creating subdisk : Subdisk offset violates disk group alignment Solution This error occurs if the offset specified does not line up correctly with existing subdisks

Attachment Products Subscribe to Article Search Survey Did this article answer your question or resolve your issue? Error V 5 1 10127 Creating Volume After restoring a disk group configuration, use the following command to recreate the site records manually: # vxdg -g diskgroup addsite site [584200] Intelligent Storage Provisioning known issues Number of columns United States Products Threat Protection Information Protection Cyber Security Services Website Security Small Business CustomerOne Products A-Z Services Business Critical Services Consulting Services Customer Success Services Cyber Security Services Education Services This command cannot be used on bootable volumes that contains root or swap volume groups.

Terms of use for this information are found in Legal Notices. In particular, shared disk groups are marked disabled and no information about them is available during this time. Education Services Maximize your product competency and validate technical knowledge to gain the most benefit from your IT investments. If this node later joins the cluster as the master while these volumes are still open, the presence of these volumes does not cause a problem.

Error V 5 1 10127 Creating Volume

the mirror rebuilds and immediatly the disk stor01_lun01 was in state FAILING again. Create recovery image using Ignite-UX recovery command. Error V 5 1 10127 After all I found out that the DCO log volume oraracvol01_dco uses space from the original luns (stor01_lun02 and stor02_lun02). Vxvm Vxvol Error V 5 1 10127 Are you sure you want to disable it?

If you subsequently increase the size of the volume, its subdisks are not grown using contiguous disk space unless you specify the attribute layout=nodiskalign to vxassist, as shown here: # vxassist http://smartphpstatistics.com/error-v/vxvm-vxdg-error-v-5-1-585-error-in-cluster-processing.html No Yes How can we make this article more helpful? Is not required to manually change the size of the volumes on the itool() File System tab, because the nearest aligned size will be automatically used. 3. So I deceided to remove the entire plex and to setup up again. Vxvm Vxassist Error V 5 1 10127

If you intend to use EMC PowerPath for multipathing, please refer to "Third-party driver coexistence" in the "Administering disks" chapter of the Veritas Volume Manager Administrator's Guide. If the final layout is not what you intended, there are two solutions: If the task is not complete, stop the relayout and reverse it by using the following command: # For example, for a network base recovery: # make_net_recovery -v -s igniteserver -x inc_entire=rootdg 2. this contact form For example, you might end up with a stripe-mirror volume instead of a mirror-stripe volume.

Sorry, we couldn't post your feedback right now, please try again later. You must first reattach the site and recover the disk group by running these commands: # vxdg -g diskgroup reattachsite sitename # vxrecover -g diskgroup The vxdiskadm command gives an Interpreting output from vxassist snapprint The output from the vxassist snapprint command for Persistent FastResync and Non-Persistent FastResync differs as follows: Persistent FastResync maintains separate tracking maps for the original volume

Powered by Blogger.

Provide feedback on this article Request Assistance Print Article Subscribe to this Article Manage your Subscriptions Search Again Situation When trying to rebuild diskgroup using the config dump, vxmake command will With 4.0 and above, when a disk is initialized from command line (vxdisksetup) or VEA by default, sets the disk layout to type "cdsdisk". Thank You! A plex can be marked stale or iofail as a result of a disk failure or an I/O failure.

Controller states Controller states may be reported as ''Not Healthy'' when they are actually healthy, and ''Healthy'' when they are actually not healthy. [599060] Remote Mirror (campus cluster) There is no Suggested Solution: Check the volumes before starting the application or place a sleep (sleep sec) before the last invocation of vxrecover. Nagiosgraph allows you to add very nice graph... navigate here Provided that you stop all volume activity before removing the package, you can ignore any errors that you see about these processes or drivers failing to start. [591547] Default I/O policy

Symantec Connect User-to-user forums, blogs, videos, and other community resources on Symantec Connect. Restart the VEA service: # /opt/VRTS/bin/vxsvcctrl start To display the state of the VEA service, enter the command: # /opt/VRTS/bin/vxsvcctrl status Veritas Volume Manager Web GUI known issues Mirroring volumes across